05. Department of Mechanical Engineering: Recent submissions

  • Khara, Jignesh; Jani, Shivang; Acharya, G.D. (Trends in Mechanical Engineering & Technology, STM Journals, 2017)
    Now a day due to the advent of technology, newer materials are coming day by day in the market, due to which it is difficult for an operator to choose the proper cutting parameter for a tool-workpiece combination to ...
  • Dudhatra, A.; Jani, S. (International Journal of Futuristic Trends in Engineering and Technology, 2014)
    Machine tool industry has undergone with various changes to meet the requirement of customer and to manufacture the complex parts. The fixtures were developed for various machining process. Fixture study had begun ...
  • Vakani, Chirag; Jani, Shivang (IJSRD - International Journal for Scientific Research & Development, 2014)
    Jib cranes are widely used in industrial facilities all over the world. A typical jib crane consists of a top beam which is rotating around a fixed column. This configuration may be referred to as an L-shaped structure. ...
  • Sheladiya, Manojkumar; Acharya, Shailee; Acharya, G.D. (Jurnal Kejuruteraan, 2023)
    The foundries are facing problem-related to the selection of the parameter’s value for minimum rejection and maximum productivity. The furan no-bake binders system guaranteed dimensional stability and a comparative good ...
  • Sheladiya, Manojkumar; Acharya, Shailee; Acharya, G.D. (International Journal of Cast Metals Research, 2022)
    In foundries, it becomes necessary to minimize the machining allowance for economic reasons. It will save resources and costs by reducing the energy and expenses incurred on re-melting, machining and tooling. A deeper ...
  • Shukla, A.; Jadeja, I. J.; Acharya, G. D. (Journal of Production Research & Management, 2016)
    The modern era of manufacturing sector and industrialization mainly focuses on the productivity improvement. To achieve the same the manufacturing cost of the various products of the industry has a profound impact. ...
  • Maru, Darshak N.; Acharya, Shailee G.; Sheladiya, Manojkumar V.; Acharya, G.D. (Industrial Engineering Journal., 2021-02-01)
    In the current increasingly competitive world of work, it is very important to constantly improve, to be efficient and effective, meeting with highquality standards. Lean Manufacturing tools are one of the most influential ...
  • Dharaiya, Vishesh.; Panchal, Avinash.; Acharya, G.D. (SN Applied Sciences, 2021-07-07)
    In this study, experiments without interlayers and with interlayers of copper and stainless-steel sheets were performed. Design of Experiments based Full-Factorial Method was employed to generate experimental combinations. ...
  • Makwana, H.H.; Kagathara, M.S.; Vaishnav, A.V. (Trends in Mechanical Engineering & Technology, 2016-02-01)
    With increasingly short life span of consumer electronic products such as mobile phones, computers, and bags; they are becoming more fashionable and requires continuous improvement. Injection molding remains the most popular ...
  • Radadiya, A.R.; Parmar, K.V.; Acharya, G.D. (Asian International Conference on Science, Engineering & Technology, 2015-01-01)
    Today’s scenario is the convert from its traditional batch methods to lean manufacturing. Maintaining standardized conditions and procedures is key to achieving a world-class work environment. Here, the primary objective ...
  • Sangadiya, P.M.; Mohite, M.V. (International Journal of Advance Engineering and Research Development, 2015-04-01)
    Nowadays, one of the greatest challenges faced by the mankind is the increasing pollution at an alarming rate. It is causing an environmental imbalance, increase the green house effect & impact on health of human being. ...
  • Saradava, K.D.; Mandaliya, P.J.; Parsania, P.P. (Trends in Machine Design, 2016-05-01)
    In the case of power transmission sometimes a fluctuating or repetitive load comes on drive shaft or driven shaft in working condition. At that time shaft as well as gear or pulley which is mounted on the gear shaft also ...
  • Bandhu, D.; Jani, S.; Thakur, A. (International Journal of Research in Engineering, IT and Social Sciences, 2017-03-01)
    The objective of the present study is to examine the influence of ageing on mechanical properties of two dissimilar materials welded together by friction stir welding (FSW) process. The study was accomplished by altering ...
  • Patel, C.M.; Acharya, G.D. (Journal of Experimental & Applied Mechanics, 2016-04-01)
    Deflection of a beam is not only an interest for the branch of civil engineering but it has extended to many other engineering branches. Prediction of deflection for non-prismatic section with different loading conditions ...
  • Saradava, B.J. (Journal of Industrial Safety Engineering, 2016-04-01)
    At present scenario, lean manufacturing has become a worldwide phenomenon. It is quite successful in drawing the attention of companies of all sizes. A large number of organizations are following the lean technologies and ...
  • Acharya, S.G.; Vadher, J.A.; Sheladiya, M. (International Journal of Metalcasting, 2016-06-01)
    Traditional cast metal markets have been confronting incessant competition from overseas producers as their lower wage scales and environmental standards reduce their product cost. Many foundries have made changes in their ...
  • Kathwadia, A.J.; Parmar, K.V.; Acharya, G.D. (Asian International Conference on Science, Engineering & Technology, 2015-01-01)
    Life-cycle assessment (LCA), also known as life-cycle analysis, eco-balance, and cradle-to-grave analysis, is a technique to assess environmental impacts associated with all the stages of a product's life from cradle to ...
  • Pandya, H.R.; Pandya, J.G.; Acharya, G.D. (Trends in Mechanical Engineering & Technology, 2018-04-01)
    Rotating shaft and other components in pump system revolving at a speed close to the natural frequency of the system are unsafe because at natural frequency, the amplitude of vibration is highest and it generates the ...
  • Yadav, V.K.; Fulekar, M.H. (International Journal of Advance Engineering and Research Development, 2018-04-01)
    Coal fly ash is an industrial by-product produced from the burning of pulverized coal, during electricity generation in the thermal power plants. Fly ash is considered a major global pollutant due to the surplus amount of ...
  • Raviya, K.; Dwivedi, V.V.; Kothari, A.; Gohil, G. (Oriental Journal of Computer Science and Technology, 2019-10-01)
    The researcher have suggested real time depth based on frequency domain hole filling. It get better quality of depth sequence generated by sensor. This method is capable to produce high feature depth video which can be ...

Search DSpace


Advanced Search

Browse

My Account